PINS, ANCHORS, RETAINING RINGS 6-43 1830 Ellsworth Industrial Dr NW, Atlanta, GA 30318 | 800.556.3967 | momar.com ANCHORS All trademarks and brand names are the property of their respective owners. See back page for copyright details. Anti-rotation serrated washer prevents anchor back-out Extra large hex washer head with increased bearing surface means a 3/8" LDT can be used to do a 1/2" wedge anchor application Length identification head stamp for embedment inspection after installation Dust relief tip automatically removes dust – no cleaning necessary Dia. (Inches) Length (Inches) Length Identification Code Drill Size (Inches) Thread Length (Inches) Across Flats (Inches) Item No. Pkg. Qty. 3/8 2-1/2 C 5/16 2-1/8 9/16 NS142946 10 3 D 5/16 2-5/8 9/16 NS142947 10 1/2 3 D 7/16 3 3/4 NS133729 10 4 F 7/16 4 3/4 NS133730 10 5 H 7/16 5 3/4 NS133731 10 LDT (Large Diameter Tapcon®) Anchors Length Identification Code is located on the anchor head for easy identification and inspection 2. Using a 1/2" impact wrench, drive anchor until fully seated. 1. Using the correct diameter carbide tipped bit, drill a pilot hole at least 1/4" deeper than anchor embedment. Ultimate* Shear and Tension Values in Normal Hollow and Grout-Filled Block Anchor Dia. (Inches) Embedment Depth Inches (mm) Hollow Concrete Block Tension (Lbs.) Hollow Concrete Block Shear (Lbs.) Grout-Filled Concrete Block Tension (Lbs.) Grout-Filled Concrete Block Shear (Lbs.) 3/8 1-1/2 (38.1) 1,525 4,538 2,655 5,569 1/2 2-1/2 (63.5) – – 5,925 6,678 *Allowable load should not exceed 25% of ultimate load values Ultimate* Shear and Tension Values in Normal Weight Concrete Anchor Dia. (Inches) Embedment Depth Inches (mm) 200 PSI Tension (Lbs.) 200 PSI Shear (Lbs.) 4,000 PSI Tension (Lbs.) 4,000 PSI Shear (Lbs.) 3/8 1-1/2 (38.1) 2,226 3,012 3,281 4,994 3/8 2 (50.8) 3,086 4,505 5,788 4,994 1/2 2-1/2 (63.5) 3,540 6,084 5,743 6,877 1/2 3-1/2 (88.9) 8,700 6,639 10,219 7,134 1/2 4-1/2 (114.3) 11,081 8,462 12,070 8,462 *Allowable load should not exceed 25% of ultimate load values • High performance, high production, self-threading anchor • Carbon steel with zinc plating • Removable • Low slippage • Ideal for stadium seating, racking, shelving and conveyors • High shear strength • Finished head • Vibration-resistant Model NS126535 Installation Tool Kit for UltraCon® Anchors • Multipurpose installation tool that is inserted into the 3/8" or 1/2" chuck of a standard hammer drill or electric drill • Drives 3/16" and 1/4" Slotted Hex Head and Phillips Flat Head UltraCon® Anchors 1/4" Socket #3 Bit #2 Bit 5/16" Socket 1/8" Hex Key Phillips Socket Drill Adapter Sleeve Assembly 3. Drive anchor 2. Install drive sleeve over drill bit 1. Drill hole Description Item No. Pkg. Qty. Model NS126535 Installation Tool Kit NS153380 1 1/8" Hex Key (use with adapter NS153381) NS130086 5 Drill Adapter NS153381 1 Sleeve Assembly NS153382 1 5/16" Socket for 1/4" Anchors NS153383 1 1/4" Socket for 3/16" Anchors NS153384 1 Phillips Socket 96946 1 #2 Phillips Bit for 3/16" Anchors NS177752 1 #3 Phillips Bit for 1/4" Anchors NS177757 1 UltraCon® SDS Shank Rotohammer Drill Bits NOTE: For more SDS shank drill bits, refer to the masonry drill bit pages in the Cutting Tools Section. UltraCon® is a registered trademark of Acument Intellectual Properties, LLC. Dia. (Inches) For Use With Item No. Pkg. Qty. 5/32 All 3/16" UltraCon® Anchors; Model NS126535 Installation Tool NS144346 1 3/16 All 1/4" UltraCon® Anchors; Model NS126535 Installation Tool NS153379 1 1/4 All 5/16" UltraCon® Anchors NS154146 1
